Pull to refresh

Comments 14

Хорошая работа. А это у вас хобби или действительно такая работа за которую платят?
На 66% хобби (интерес все разбирать и смотреть что внутри думаю был когда-то у всех), 34% работа — но за которую платить пришлось бы самому себе :-) Есть ряд компаний, подобную работу выполняющие на коммерческой основе (и в России тоже).

В моем случае эти 34% работы — смотреть на коммерческие продукты в интересующих областях, оценивать технологию, себестоимость и сложность разработки. Эти результаты затем ложатся в основу бизнес-плана и проч.
Как вы точно посчитали процент)
Две трети — одна треть :)
Под RGB мерцающим светодиодом понимается тот, который моргает разными цветами или плавно переключателя между ними? Интересно было бы посмотреть на разницу начинки между ними.
Там у него несколько режимов работы, разные алгоритмы мерцания и он по очереди переключается между ними.
Да, RGB разных тоже много… И ведь люди сидят, разрабатывают эти разные моргающие светодиоды…

Тот что у меня — вот так работает:
А некоторые потом сидят и реверсят моргающие светодиоды, а мы потом сидим и завороженно смотрим на их фотографии))
В этот тред надо отправлять всех мигателей светодиодами на Raspberry PI
Так это, выходит, не микроконтроллер, а цифровая схема, сделанная под эту конкретную задачу?
Я правильно понял, что такие диоды можно подключать прямо к источнику напряжения без резистора? Если да, то сколько В?
Да, можно напрямую. 3.3-5В, больше 5 — слишком большой ток и температура, сгорят со временем :-)
Нашел на просторах интернета:



Upper left is GND pad.
Lower right is VCC pad.
Upper right is output to LED anode.

To the left of the LED output pad is the large serpentine LED driver transistor.

Between the GND pad and serpentine transistor is Power on Reset with the metal plate the capacitor and a long trace loop to form a resistor for an RC time constant.

In the lower region, to the left of the VCC pad, is a similar pad which forms a capacitor. With the serpentine resistor connected to the upper left of this pad, this, forms the on board RC oscillator. The drive transistor is center bottom with four T-flip-flop divider stages repeated to the lower left of the chip.

The middle of the chip has three horizontal bands.

The upper band (just below the GND pad and extending across to the LED pad) is a 9-stage divider chain along with miscellaneous logic at right. This divides down the RC clock. Additionally various taps from the divider chain are used in the second horizontal region.

The second horizontal region has several EXOR gates (center) which combine outputs from the divides chain, along with various outputs from region three below.

Region three has several cells wired as shift registers. Near the left is misc logic, then two shift rigisters, then an EXOR gate, then five additional shift register cells. At the far right is a buffer which then drives the previously mentioned large serpentine transistor to the LED pad.

The shift register cells are very similar to the T-flip-flop cells used in the 9-stage divider chain, but wired differently.
Sign up to leave a comment.