Полупассивное охлаждение компьютерного БП

// 2 - DS18x20 data
// 3 - green LED (a 330 Ohm resistor is necessary)
// 5 - orange LED (a 330 Ohm resistor is necessary)
// 6 - red LED (a 330 Ohm resistor is necessary)
// 9 - PWM Fan
// 8 - Buzzer

#include <OneWire.h>

byte temp; // temperature of sensor
byte greenLED = 3;
byte orangeLED = 5;
byte redLED = 6;
byte FanSpeed = 0;
int piezoPin = 8;
// Массив режимов работы светодиода
byte modes[] = {
   0B00000001, //Светодиод выключен
   0B00000101, //Горит постоянно
   0B00010101, //Мигание по 0.5 сек
   0B01010101, //Короткая вспышка раз в секунду
   0B10101010, //Две короткие вспышки раз в секунду
   0B00010101, //Три короткие вспышки раз в секунду
   0B01010101  //Частые короткие вспышки (4 раза в секунду)
};

uint32_t ms, ms1 = 0, ms2 = 0, ms3 = 0, ms4 = 0, ms5 = 0;
uint8_t  blink_loop = 0;
uint8_t  blink_mode = 0;
uint8_t  modes_count = 0; 
bool FirstRun = 0;

OneWire  ds(2);  // on pin 10 (a 4.7K resistor is necessary)

void analogWrite25k(int pin, int value)
{
    switch (pin) {
        case 9:
            OCR1A = value;
            break;
        case 10:
            OCR1B = value;
            break;
        default:
            // no other pin will work
        break;
    }
}

void setup(void) {

pinMode(redLED, OUTPUT);
pinMode(greenLED, OUTPUT);
pinMode(orangeLED, OUTPUT);
pinMode(9, OUTPUT);

modes_count = 1;
blink_mode = modes[modes_count];

    TCCR1A = 0;           // undo the configuration done by...
    TCCR1B = 0;           // ...the Arduino core library
    TCNT1  = 0;           // reset timer
    TCCR1A = _BV(COM1A1)  // non-inverted PWM on ch. A
           | _BV(COM1B1)  // same on ch; B
           | _BV(WGM11);  // mode 10: ph. correct PWM, TOP = ICR1
    TCCR1B = _BV(WGM13)   // ditto
           | _BV(CS10);   // prescaler = 1
    ICR1   = 200;         // TOP = 320
  
 // Serial.begin(9600);
 

}

void loop() {
  byte i;
  byte present = 0;
  byte type_s;
  byte data[12];
  byte addr[8];
  float celsius;

 if ( ( ms - ms3 ) > 1000 || ms < ms3 ){
       ms3 = ms;
  
     if ( !ds.search(addr)) {
      //   Serial.println("No more addresses.");
      //   Serial.println();
         ds.reset_search();
         if ( ( ms - ms4 ) > 250 || ms < ms4 ){
         ms4 = ms;
         //delay(250);
    return;
      }
     }
  
     //  Serial.print("ROM =");
  for( i = 0; i < 8; i++) {
    //   Serial.write(' ');
     //  Serial.print(addr[i], HEX);
       }

  if (OneWire::crc8(addr, 7) != addr[7]) {
    // Serial.println("CRC is not valid!");
      return;
  }
       
      // Serial.println();
 
  // the first ROM byte indicates which chip
  switch (addr[0]) {
    case 0x10:
      Serial.println("  Chip = DS18S20");  // or old DS1820
      type_s = 1;
      break;
    case 0x28:
      Serial.println("  Chip = DS18B20");
      type_s = 0;
      break;
    case 0x22:
      Serial.println("  Chip = DS1822");
      type_s = 0;
      break;
    default:
      Serial.println("Device is not a DS18x20 family device.");
      return;
  } 

  ds.reset();
  ds.select(addr);
  ds.write(0x44, 1);        // start conversion, with parasite power on at the end
 
 }
  
  //delay(1000);     // maybe 750ms is enough, maybe not
  // we might do a ds.depower() here, but the reset will take care of it.

  if ( ( ms - ms2 ) > 900 || ms < ms2 ){
       ms2 = ms;
       
  present = ds.reset();
  ds.select(addr);    
  ds.write(0xBE);         // Read Scratchpad

  for ( i = 0; i < 9; i++) {           // we need 9 bytes
    data[i] = ds.read();

  }


  // Convert the data to actual temperature
  // because the result is a 16 bit signed integer, it should
  // be stored to an "int16_t" type, which is always 16 bits
  // even when compiled on a 32 bit processor.
  int16_t raw = (data[1] << 8) | data[0];
  if (type_s) {
    raw = raw << 3; // 9 bit resolution default
    if (data[7] == 0x10) {
      // "count remain" gives full 12 bit resolution
      raw = (raw & 0xFFF0) + 12 - data[6];
    }
  } else {
    byte cfg = (data[4] & 0x60);
    // at lower res, the low bits are undefined, so let's zero them
    if (cfg == 0x00) raw = raw & ~7;  // 9 bit resolution, 93.75 ms
    else if (cfg == 0x20) raw = raw & ~3; // 10 bit res, 187.5 ms
    else if (cfg == 0x40) raw = raw & ~1; // 11 bit res, 375 ms
    //// default is 12 bit resolution, 750 ms conversion time
  }
  celsius = (float)raw / 16.0;
  
  temp = celsius;

 // Serial.println("TEMPERATURE IS:");
 // Serial.println(temp);
 }
     
    ms = millis();
// Событие срабатывающее каждые 125 мс   
   if( ( ms - ms1 ) > 125|| ms < ms1 ){
       ms1 = ms;
       
// Режим светодиода ищем по битовой маске       

  if ( temp <= 50 ) {
       digitalWrite(orangeLED, LOW);
       digitalWrite(redLED, LOW);
       if(  blink_mode & 1<<(blink_loop&0x07) ) digitalWrite(greenLED, HIGH); 
       else  digitalWrite(greenLED, LOW);
       blink_loop++;    

       

                 if ( temp <= 40 ) {
                 blink_mode = modes[0];
                 analogWrite25k ( 9, 0);
                 FirstRun = 0;
                }
                 if ( temp >= 41 && temp <= 45 ) {
                 blink_mode = modes[1];

// Make a push impulse for starting fan (1 sec)
                 
                 if ( FirstRun == 0 ) {
                     ms5 = ms;
                     FirstRun = 1; 
                 }

                 if (FirstRun == 1 && (2000 > (ms - ms5))) { 
                    analogWrite25k ( 9, 33); // Fan start impulse
                 }
                 if (FirstRun == 1 && (2000 < (ms - ms5))) {
                 analogWrite25k ( 9, 28); // first speed
                 }
              }
                 if ( temp >= 46 && temp <= 50 && FirstRun == 1) {
                 blink_mode = modes[2];
                 analogWrite25k ( 9, 29);
                 }
      }

  
  if ( temp >= 51 && temp <= 61 ) {
       digitalWrite(greenLED, LOW);
       digitalWrite(redLED, LOW);
       if(  blink_mode & 1<<(blink_loop&0x07) ) digitalWrite(orangeLED, HIGH); 
       else  digitalWrite(orangeLED, LOW);
       blink_loop++;    
    

                if ( temp >= 51 && temp <= 54 ) {
                 blink_mode = modes[0];
                 analogWrite25k ( 9, 30);
                }
                 else if ( temp >= 55 && temp <= 58 ) {
                 blink_mode = modes[1];
                 analogWrite25k ( 9, 31);
                }
                 else if ( temp >= 59 && temp <= 61) {
                 blink_mode = modes[2];
                 analogWrite25k ( 9, 32);
                }
      }
   
     if ( temp >= 62 && temp <= 120 ) {
       digitalWrite(greenLED, LOW);
       digitalWrite(orangeLED, LOW);
       if(  blink_mode & 1<<(blink_loop&0x07) ) digitalWrite(redLED, HIGH); 
       else  digitalWrite(redLED, LOW);
       blink_loop++;    
    

                if ( temp >= 62 && temp <= 66 ) {
                 blink_mode = modes[0];
                 analogWrite25k ( 9, 33);
                }
                if ( temp >= 67 && temp <= 70 ) {
                 blink_mode = modes[1];
                 analogWrite25k ( 9, 34);
                }
                if ( temp >= 71 && temp <= 120) {
                 blink_mode = modes[2];
                 analogWrite25k ( 9, 50);
                 tone(piezoPin, 2500, 30);
                }
      }
   
   }  
 
}