Замена аналоговой регулировки на цифровую в лабораторном блоке питания HY3005D

// PIC16F1829 Configuration Bit Settings

// 'C' source line config statements

#include <xc.h>

// #pragma config statements should precede project file includes.
// Use project enums instead of #define for ON and OFF.

// CONFIG1
#pragma config FOSC = INTOSC    // Oscillator Selection (INTOSC oscillator: I/O function on CLKIN pin)
#pragma config WDTE = OFF       // Watchdog Timer Enable (WDT disabled)
#pragma config PWRTE = OFF      // Power-up Timer Enable (PWRT disabled)
#pragma config MCLRE = OFF      // MCLR Pin Function Select (MCLR/VPP pin function is digital input)
#pragma config CP = OFF         // Flash Program Memory Code Protection (Program memory code protection is disabled)
#pragma config CPD = OFF        // Data Memory Code Protection (Data memory code protection is disabled)
#pragma config BOREN = OFF      // Brown-out Reset Enable (Brown-out Reset disabled)
#pragma config CLKOUTEN = OFF   // Clock Out Enable (CLKOUT function is disabled. I/O or oscillator function on the CLKOUT pin)
#pragma config IESO = OFF       // Internal/External Switchover (Internal/External Switchover mode is disabled)
#pragma config FCMEN = OFF      // Fail-Safe Clock Monitor Enable (Fail-Safe Clock Monitor is disabled)

// CONFIG2
#pragma config WRT = OFF        // Flash Memory Self-Write Protection (Write protection off)
#pragma config PLLEN = OFF      // PLL Enable (4x PLL disabled)
#pragma config STVREN = ON      // Stack Overflow/Underflow Reset Enable (Stack Overflow or Underflow will cause a Reset)
#pragma config BORV = LO        // Brown-out Reset Voltage Selection (Brown-out Reset Voltage (Vbor), low trip point selected.)
#pragma config LVP = OFF        // Low-Voltage Programming Enable (High-voltage on MCLR/VPP must be used for programming)

#include "config.h"

#define _XTAL_FREQ 32000000
#pragma intrinsic(_delay)
extern void _delay(unsigned long);
#define __delay_us(x) _delay((unsigned long)((x)*(_XTAL_FREQ/4000000.0)))
#define __delay_ms(x) _delay((unsigned long)((x)*(_XTAL_FREQ/4000.0)))

#define TransferNotDone          !(SSP2STAT&0b00000001)

#define StoreAll                 LATA4
#define ResetAll                 LATC6

#define VoltageSharpCHA          RC1
#define VoltageSharpCHB          RC0
#define VoltageSharpBTN          RA2

#define VoltageSmoothCHA         RB5
#define VoltageSmoothCHB         RB4
#define VoltageSmoothBTN         RC2

#define CurrentSharpCHA          RC5
#define CurrentSharpCHB          RC4
#define CurrentSharpBTN          RC3

#define CurrentSmoothCHA         RA1
#define CurrentSmoothCHB         RA0
#define CurrentSmoothBTN         RA3

#define VoltageRateSharp         0x0100
#define VoltageRateSmooth        0x0010
#define CurrentRateSharp         0x0040
#define CurrentRateSmooth        0x0004

#define VoltageMax               0xC000
#define CurrentMax               0x5000
#define VoltageMin               0x0000
#define CurrentMin               0x0000

#define VoltageStart             0x1E00
#define CurrentStart             CurrentMax

unsigned short VoltageBuff;
unsigned short CurrentBuff;

void interrupt tc_int() {
};

void SendData() {
    SSP1BUF = VoltageBuff>>8;
    SSP2BUF = CurrentBuff>>8;
    while ( TransferNotDone );
    SSP1BUF = VoltageBuff;
    SSP2BUF = CurrentBuff;
    while ( TransferNotDone );
    StoreAll = 1;
    StoreAll = 0;
};

void main() {
    // Configure oscillator for 32MHz
    //             76543210
    OSCCON     = 0b11110000; //B1

    // Enable individual pull-ups
    //             76543210
    OPTION_REG = 0b01111111; //B1

    // Configure analog port (1 - enable, 0 - disable)
    //             76543210
    ANSELA     = 0b00000000; //B3
    ANSELB     = 0b00000000; //B3
    ANSELC     = 0b00000000; //B3

    // Reset latch
    //             76543210
    LATA       = 0b00000000; //B2
    LATB       = 0b00000000; //B2
    LATC       = 0b00000000; //B2

    // Alternate pin function (set SDO2 on RA5)
    //             76543210
    APFCON0    = 0b00000000; //B2
    APFCON1    = 0b00100000; //B2

    // Configure digital port (1 - input, 0 - output)
    //             76543210
    TRISA      = 0b00001111; //B1
    TRISB      = 0b00110000; //B1
    TRISC      = 0b00111111; //B1

    // Configure input level (1 - CMOS, 0 - TTL)
    INLVLA     = 0b11000000; //B7
    INLVLB     = 0b00001111; //B7
    INLVLC     = 0b00000000; //B7

    // Configure individual pull-ups (1 - enable, 0 - disable)
    //             76543210
    WPUA       = 0b00111111; //B4
    WPUB       = 0b11110000; //B4
    WPUC       = 0b11111111; //B4

    ResetAll = 0;
    ResetAll = 1;

    // Configure SPI in master mode
    //             76543210
  //SSP1ADD    = 0b00000000; //B4
    SSP1STAT   = 0b01000000; //B4
    SSP1CON3   = 0b00000000; //B4
    SSP1CON1   = 0b00100000; //B4
  //SSP1ADD    = 0b00000000; //B4
    SSP2STAT   = 0b01000000; //B4
    SSP2CON3   = 0b00000000; //B4
    SSP2CON1   = 0b00100000; //B4

    VoltageBuff = VoltageStart;
    CurrentBuff = CurrentStart;
    __delay_ms(50);
    SendData();

    while ( 1 ) {
        if ( !VoltageSharpCHA ) {
            if ( VoltageSharpCHB ) { VoltageBuff-=VoltageRateSharp; if ( VoltageBuff > VoltageMax ) VoltageBuff = VoltageMin; }
                              else { VoltageBuff+=VoltageRateSharp; if ( VoltageBuff > VoltageMax ) VoltageBuff = VoltageMax; }
            while ( !VoltageSharpCHA );
            SendData();
        }

        if ( !VoltageSmoothCHA ) {
            if ( VoltageSmoothCHB ) { VoltageBuff-=VoltageRateSmooth; if ( VoltageBuff > VoltageMax ) VoltageBuff = VoltageMin; }
                               else { VoltageBuff+=VoltageRateSmooth; if ( VoltageBuff > VoltageMax ) VoltageBuff = VoltageMax; }
            while ( !VoltageSmoothCHA ); 
            SendData();
        }

        if ( !CurrentSharpCHA ) {
            if ( CurrentSharpCHB ) { CurrentBuff-=CurrentRateSharp; if ( CurrentBuff > CurrentMax ) CurrentBuff = CurrentMin; }
                              else { CurrentBuff+=CurrentRateSharp; if ( CurrentBuff > CurrentMax ) CurrentBuff = CurrentMax; }
            while ( !CurrentSharpCHA );
            SendData();
        }

        if ( !CurrentSmoothCHA ) {
            if ( CurrentSmoothCHB ) { CurrentBuff-=CurrentRateSmooth; if ( CurrentBuff > CurrentMax ) CurrentBuff = CurrentMin; }
                               else { CurrentBuff+=CurrentRateSmooth; if ( CurrentBuff > CurrentMax ) CurrentBuff = CurrentMax; }
            while ( !CurrentSmoothCHA );
            SendData();
        }

        if ( !VoltageSharpBTN  ) { VoltageBuff = VoltageMax; while ( !VoltageSharpBTN  ); SendData(); }
        if ( !VoltageSmoothBTN ) { VoltageBuff = VoltageMin; while ( !VoltageSmoothBTN ); SendData(); }
        if ( !CurrentSharpBTN  ) { CurrentBuff = CurrentMax; while ( !CurrentSharpBTN  ); SendData(); }
        if ( !CurrentSmoothBTN ) { CurrentBuff = CurrentMin; while ( !CurrentSmoothBTN ); SendData(); }
    };
}